Scytek electronic VISIONGUARD 6000 Instrukcja Obsługi Strona 7
- Strona / 36
- Spis treści
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Adding/Replacing Transmitters
To replace lost or stolen transmitters or to add additional transmitters into the system, have all desired
transmitters ready and follow the steps below.
Note: Up to 4 transmitters can be programmed to operate the system. To erase any previously stored
transmitter codes, be sure to program all 4 transmitter memory locations.
To program the transmitter(s):
1. Turn on the ignition key On, Off, On, Off, and back On. (Key On 3 times)
· The siren will chirp 3 times.
2. Press and hold the Override switch for 5 seconds.
· The siren will chirp 5 times.
· The LED will illuminate.
3. Press Button 1 on the first transmitter.
· The siren will chirp once.
4. Press Button 1 on the first transmitter again.
· The siren will chirp twice to indicate it has learned the code.
5. Repeat steps 3 and 4 for each transmitter (up to 4).
6. Turn off the ignition key.
Two Car Operation
If two vehicles are equipped with Visionguard 6000 systems, for convenience both can be operated using
the same remote transmitter. If all four transmitters are to be used with both cars, program transmitters
A and B into the first vehicle in the manner described above. Program transmitters C and D by pressing
the Shift button twice before performing steps 3 and 4 above.
When finished programming the first vehicle, program transmitters C and D into the second vehicle as
normal, then program transmitters A and B by pressing the Shift button twice before performing steps 3
and 4 above.
When programmed in this manner, the driver of the first car can also operate the second vehicle by pressing
the Shift button twice and the desired function button.
Battery Replacement
Your Remote Transmitter uses two 3 volt lithium batteries (type CR2016), which will require
replacement in time. Depending on the amount of use, the batteries may last up to six months
or more before they need replacement.
In order to change the battery, first remove the screw from the back of the transmitter and separate the
top and bottom halves of the case.
While replacing the battery make sure that the positive and negative terminals are positioned correctly, then
carefully reassemble the transmitter case.
VisionGuard 6000 - Page 3
- VISIONGUARD 1
- Limited 2
- Lifetime 2
- Warranty 2
- Contents 3
- System Contents: 5
- Transmitters 6
- Two Car Operation 7
- Battery Replacement 7
- Page 4 - VisionGuard 6000 8
- System Confirmation 9
- Features 10
- VisionGuard 6000 - Page 7 11
- Operation 12
- Tamper Alert 13
- Silent Arming/Disarming 13
- Passive Arming 13
- Panic Mode 14
- Emergency Override 14
- Automatic Rearming 15
- Valet Mode 15
- Turbo Timer Feature 17
- Remote Starting 17
- Shut Down 17
- Extended 18
- Installation 19
- Mounting the Control Unit 20
- Mounting the Siren 20
- Mounting the Shock Sensor 20
- 6-Pin Starter Harness 21
- 20-Pin Main Harness 21
- Plug-in Connectors 22
- Settings 23
- Programming 24
- VisionGuard 6000 - Page 21 25
- Page 22 - VisionGuard 6000 26
- VisionGuard 6000 - Page 23 27
- Diagrams 28
- Green Wire 29
- Blue Wire 29
- Two Stage Reverse Polarity 31
- Two Stage Adding Actuators 31
- Technical 32
- Information 32
- Starter Diagnostics 33
- Page 30 - VisionGuard 6000 34
- VisionGuard 6000 - Page 31 35
- VisionGuard 6000 36
Powiązane produkty i podręczniki dla Alarm samochodowy Scytek electronic VISIONGUARD 6000
(28 strony)Samsung DB400S6B manuály
Uživatelské manuály a uživatelské příručky pro ne Samsung DB400S6B.
Poskytujeme 2 manuály pdf Samsung DB400S6B ke stažení zdarma podle typů dokumentů: Uživatelský manuál
Komentarze do niniejszej Instrukcji